86-0536-5209317
No. 301, Guangyao Shengdi Building, Wensheng Street, Shouguang, Shandong, China (Mainland)
high polymer waterproof polyethylene sheet membrane
PP+PE+PP composite waterproof membrane is made by multiple-ply different materials, especially its aging
and weathering resistance layer enables the membrane possess more longer effective age. It can bond with many kinds of adhesions, firm and secure. In case of cement-base, cementations agent can be used, the
cementations agent can easily enter into the non-woven felt layer, forms a well-combination with cement after
solidification, permanent durability.
1. Non-toxic, no pollution, environmental protecting product.
2. Can be used for many different surfaces, especially for cement basement.
3. Tough, impermeable, multi-layered sheet;
4. High tension strength, good cold flexibility.
1. The application is simple and no-pollution. It is mainly used in the middle of building for waterproofing. On this layers of protection and decoration are needed;
2. When application, pour the adhesive materials homogeneously on the smooth roof deck, then roll the membrane to make is fully adhered to the deck.
3. The adhesive materials are usually made form cement or other building glue.
Products used in roofing, basement, restroom, water conservation, warehouse to protect structure from water infiltration.
1. The application is simple and no-pollution. It is mainly used in the middle of building for waterproofing. On this layers of protection and decoration are needed;
2. When application, pour the adhesive materials homogeneously on the smooth roof deck, then roll the membrane to make is fully adhered to the deck.
3. The adhesive materials are usually made form cement or other building glue.
Construction procedures:
Check leveling layer→Clean-up basic level →Preparation the cement binder→Do additional layer→Base
construction→protective layer→Curing
1)The basic level must be clean, keeping moist.
2)Preparing cement paste, containing cement weighing 10% -15% polyvinyl binder,Mixing must be homogeneous,No precipitation,No clot,No segregation phenomenon can be used.
3)Before the construction of the main roof waterproof layer,firstly, the drainage and the places of complex structure should be dealled with well. The waterproof membrane on the the additional layer is the same as the main waterproof layer.4)The seal material can use poly ether type polyurethane, if use other sealing materials , they should be free of mineral oil, petrolatum and other chemical substances affecting the performance of polyethylene products.
5)Corner should be paved by the additional layer; yin and yang angle, etc. are made of R = 20mm arc-shaped.
6)Waterproofing membrane should be paved, adhesive should be homogeneous on the basic level surface, after that immediately pave the waterproof membrane , in case of affecting the bond quality.
7)Paving the waterproofing membrane shall not wrinkle, not forcibly stretch the membrane, the air and the excess adhesive below the membrane should be dealled with well while paving the membrane, ensure the membrane spliced well with the primary surface and between the layers of membrane.
8)The lap width of the waterproofing membrane shall be not less than 100mm.
9)Upper-and-lower level and the adjacent membrane should be staggered to one-third of magnitude.
Put about 50kg-60kg cool water into the mixer, then moving the mixer and put 1 bag (500g)of the adhesive
powder slowly, then mix it for 3-5 minutes to the sticky extent, and then put 2-3 bags ( one bag is about 50kg )of the cement mixing homogeneously. ( 1 bag of the adhesive powder will be enough for about 80 sqm ).
If the construction is erect structure, it is about 50kg cool water, 1 bag of adhesive powder(about 50g) and 2 bags cement(about 100kg), if it is plane structure, you may obey the proportion in the first step mentioned.
The adhesive powder can only mix with the cement, the bonding strength can be up to the maximum after the cement becomes totally dry.
Packing Details : Packing with woven bag and put in pallet(customized)
Delivery Details : 3-10 days after received the prepayment
A: We are factory.
A: Generally it is 5-10 days if the goods are in stock. or it is 15-20 days if the goods are not in stock, it is according to quantity.
A: Yes, we could offer the sample for free charge but do not pay the cost of freight.
A: Payment<=1000USD, 100% in advance. Payment>=1000USD, 30% T/T in advance ,balance before shippment.
If you have another question, pls feel free to contact us as below:
